Gimmick Mods – Page 3 – MagicShow.Tips

Three Inches Too Long…

Yesterday I was back home briefly before flying to Los Angeles to record a few routines for a TV show. While I was packing up to fly, I learned that the speaker stand that I’ve been using in my virtual shows as my table base didn’t fit into my case, it was about 3 inches too long! I switched to using a speaker stand early into doing virtual shows because I was able to raise it higher than a traditional magician’s table. That made it easier to frame my face and table in the same camera shot. You can read more about that here:

http://www.magicshow.tips/magic-show-tips/a-sturdy-base/

The solution was pretty simple, I unscrewed the attachment at the top, then cut off a few inches with my Dremel. Also if you don’t have a Dremel or similar tool, you should get one, they are super handy!

While I was out there I also noticed the smaller bar that moves up and down didn’t need to be as long as it was, so I chopped it in half. That will reduce weight for future trips if I fly with this again. Ideally I’ll just use a speaker stand provided by the venue.

Luckily it was a simple solution to shorten the speaker stand. I’ve always said that being a professional magician is 90% problem solving!

Moving Dots…

A while ago I realized that three of magic tricks I’ve developed in the last year is basically the same plot, just with different props. Three things disappear one at a time and reappear grouped together.

I’m trying to add some texture to the show. One of the things I picked up is The Matrix Pad Reloaded. While the name implies that three things would disappear and reappear in one spot like a traditional coin matrix, it’s not exactly that. It’s a moving ink effect, so not really a teleportion, or vanish and reappearance, it’s closer to an animation.

Here’s the demo of the trick:

For a virtual family show I think I could add some fun and make it more interactive. I started by adding different colored pens, so each dot is a different color. While less practical for an in person show, this change is a simple alteration of the gimmick. Now I can have three people each pick a color and I have three people involved in the trick. Then I decided we can play a bit and they will pick a mode of transportation and that’s how the dots will move.

Here’s the test run of it I did at the local magic club:

While it’s not perfect, I think that there’s something there.

Making Some Take Up Reels…

One of the magic products that I put out and that I’m the most proud of is the Take Up Reel that I created. What a Take Up Reel is used for is to shorten a length of string and was popularized by Billy McComb and Tommy Wonder in their Vanishing Birdcage routines.

As far as I know I’m currently the only person / company that makes a Take Up Reel for sale. I’m working on a batch of them this week. It takes about a full week to make one from start to finish. Here’s one of the locks coming out of my 3D printer:

Magic is being revolutionized by 3D printing, especially stage magic. It allows you to affordably make soo many custom props that would have cost tons of money to have fabricated 5 or 10 years ago.

If you’re not out printing stuff, I highly recommend learning how. It’s pretty easy, and you don’t even need to own a 3D printer as there are companies you send the file to and they’ll make it for you.

Click here for more info on my Take Up Reel!

Vertical Three Shell Game

Last night I was playing with a set of mini cups and balls that I have. This particular set was made by Leo Smesters. These are a great little set, however honestly I don’t have much of a use for them. When I originally bought them I had an idea, but haven’t done much with them.

I had the idea of doing a vertical three shell game. The ball would switch places vertically while the cups were stacked. Here’s a quick video of the basic idea:

There’s a little bit more to the full idea I have. Right now the cups are ungimmicked and they will stay that way. However the balls have magnets in them and they stick to each other through the cup. So the cups can sort of function like a chop cup or regular cup depending on the positions of the two balls.

My idea is to have one ball with a very strong magnet in it and then two others with smaller magnets in them. The audience is only aware of one ball. You will steal the ball with the strong magnet and use that magnet like you would a use thumbtip with a magnet inside of it. That will give much more options with what you can do with the cups.

Now I just need to make the balls…

Magic 3D Printing Tutorial

One thing that’s been life changing for my show is learning to use a 3D printer. Recently I was part of a panel that was talking about 3D printing for performers and I made a quick video tutorial that took you through the entire design process of making a holder for a thumb tip and dollar bill holder.

Here it is:

Hopefully this took some of the mystery out of 3D printing. Honestly I thought it would be much harder, until I got one and learned to do it!

Upgrading My Virtual Dice…

One of the things I’m always doing it trying to improve what I currently do. Right now in my virtual show I do a modified version of my Cee-Lo trick, which is a cup and dice routine. This ends with the production of two large dice. The large dice are 1 1/4 inches on each side. To give you some perspective, the picture below is one of the jumbo dice next to a regular die.

The reason that the trick uses 1 1/4 inch dice is that for a live, in person show, it makes the loading procedure work. The cup will hold two 1 1/2 inch dice, but the method where the spectator loads the cup for you doesn’t work well with a larger die.

I was cleaning up and found the old set of 1 1/2 inch dice I tried using for Cee-Lo. It hit me, since I’ve changed my loading procedure for virtual shows, and there are no spectators to handle the props, why not move to the larger size dice. To give you an idea of visually how much bigger they are, the pictures below are a 1 1/2 inch die next to a regular die and a 1 1/4 inch die.

That extra quarter inch makes it look massive! The nice thing about how I load the cups for live virtual shows is that the size of the die doesn’t really matter. I’m getting a little more visual impact for no extra work! I’m a fan of that.

Taking a Pea…

One of the silver linings about having the entertainment industry shut down during the COVID pandemic is that I’m getting play around with making a lot more props. One thing that I’ve wanted to make for a while are peas for the three shell game.

I had some time some the other day and made some molds for the peas. Then I picked up some urethane and made them. The urethane I used was a 40A on the Shore Hardness Scale.

They have a little bit of give, but are pretty firm. I like them so far!

Shell Sequence…

Yesterday I wrote a post about what playing with gimmicked shells, pea and table for the three shell game. Here’s a simple sequence I put together with them to highlight what you can do with the combination:

My end goal is going to be having “zones” on my table that make the balls appear under that specific shell. I think will have some interesting possibilities…

Table Loading…

I’m excited that my table dice holder that I was 3d printing yesterday turned out and works great! It’s for the final two dice production of my Cee-lo cup and dice routine. Here’s the finished holder:

The holder has a notch in the bottom for my finger to contact the bottom of the dice and then to lift straight up to load them into the cup. Here’s this loading procedure in a test video:

This is way better than loading from the pocket for video! I’m glad I spent the time to make it and wasn’t okay with doing it the way I’ve always done it.

Red Evaporation Trick

How I’m using the Evaporation trick in my show right now is pretty simple. I take pour red liquid into a cup and when I turn the cup over a red ball falls out. Not much to it. There is one little thing that I sometimes have to do to the liquid. Sometimes the … Continue reading “Red Evaporation Trick”

How I’m using the Evaporation trick in my show right now is pretty simple. I take pour red liquid into a cup and when I turn the cup over a red ball falls out. Not much to it.

There is one little thing that I sometimes have to do to the liquid. Sometimes the liquid it too clear, so I have to make it a little more opaque. How I do that is simple add a few drops of non-dairy creamer to it and that makes it cloudy.

Using non-dairy creamer makes cleaning up the bottle little bit easier. Something in the dairy that makes the bottle get a little gross over time. There’s no reason why you can’t use milk, or half and half as long as you clean the bottle well after each use.